Electronic Products
Find us here:
  • Books
    • Embedded C Books >
      • cbookfiles
      • cbook2files
      • cbook3files
    • BASIC Books >
      • Programming PICs in BASIC_vol1
      • PICBasic Book Support
      • Basic Atom Book Support
    • Other Books >
      • Arduino Book
      • chipkitbookfiles
  • Chuck's Blog
    • Blog Posts Archive
    • Disclaimer
  • YouTube Channel
  • About Chuck
    • About Chuck
    • Stock Car Racing
  • 3D Printing
    • Fabrikator Mini
  • Getting Started with PICs
    • BASIC Programming
    • C Programming >
      • C Compilers
  • Build Your Own PICKit 2
    • PICkit 2 Starter Kit
  • CHIPINO
    • Shields
  • CHIPAXE Breadboard Modules
  • Understanding Hex Files
  • chipKIT
  • Newsletter Archive
  • Contact
  • Retired Designs
    • BasicBoard
    • Ultimate OEM
    • Maximite BasicBox
    • Maximino
  • Downloads
  • Kickstarter Projects
    • Demo-Shield
  • Great Cow Basic Site
  • Buy Hardware
  • Links I Recommend

See Me at 2015 MakerFaire Detroit

7/9/2015

1 Comment

 
Picture
I'll be setup at Maker Faire Detroit once again!
I have been setup at the Faire every year since it started except for last year and I missed it. This gives me a chance to meet some of the readers of my books and this year I'll get to see some of the subscribers to my YouTube Channel. I look forward to that the most. I hope many can make it out to the Faire. 
Picture
This year I'm bringing my 3D printers to the Maker Faire to talk to anybody interested in getting started with 3D printing. I'm sure I'll get all kinds of questions and comments about the Da Vinci's (both good and bad) but I'm ready for the discussion. In the past I focused my booth on electronics but not this year. I'll have some of my books available but other than that the focus will be my YouTube Channel and the 3D printing.
I also plan to bring my Shapeoko CNC just to show it off and some of the projects but I won't be running anything on it. It will be there just for discussion purposes.

I'll be inside the Henry Ford Museum this year. I've been outside in the past and the heat and rain made it horrible so a nice air conditioned booth is fine for me this year. I'm not sure where I'll be positioned so you'll have to search around to find me but that's the fun part of Maker Faire. So many things to see while you search.

I hope to see you there.
1 Comment
Brian Knight link
8/2/2015 02:58:36 am

Chuck,

I've been following your YouTube videos over their last 2-3 months having reverently taken the plunge into 3D printing with a Da Vinci AiO. Learnt some great tips & getting more consistent results now.
I was a little disheartened at your departure from the XYZ software due to problems with limitations of the cartridge system. I am a 64 year old newbie to this technology with little electronics expertise and not wishing to reflash my new printer & end up destroying it !
However, I've read that the cartridge chip can be reflashed

Reply



Leave a Reply.


    Categories

    All
    3D Printer
    Chipaxe
    Chipino
    Chipkit
    CNC
    Copper Connection
    Dot Matrix
    Elproductsnews
    Expresspcb
    Graphic Lcd
    Great Cow Basic
    Kickstarter
    Lcd Shield
    Makefaire
    Makercase
    Maximite
    Microchip Pic
    Pickit 2
    Pickit 3
    Videos

    Visit previous blog posts in the archives below.

    Archives

    February 2018
    October 2017
    September 2017
    July 2017
    November 2016
    August 2016
    July 2016
    May 2016
    March 2016
    January 2016
    November 2015
    September 2015
    August 2015
    July 2015
    June 2015
    April 2015
    March 2015
    February 2015
    January 2015
    December 2014
    November 2014
    October 2014
    September 2014
    August 2014
    July 2014
    June 2014
    May 2014
    April 2014
    March 2014
    February 2014
    January 2014
    December 2013
    November 2013
    October 2013
    September 2013
    August 2013
    July 2013
    June 2013
    May 2013
    April 2013
    March 2013
    October 2012
    October 2011

    RSS Feed



    About Chuck

    Chuck has been programming with PIC Microcontrollers since there were only five devices. Now there are over 700 and growing. He also has a lot of fun 3D printing designs using his Davinci 3D printer and TinkerCad software. In this series of blog posts and occasional videos on his YouTube Channel he tries to help you get started with electronics and 3D printing.

    Disclaimer

Powered by Create your own unique website with customizable templates.